一：準備：勘察現場  人員  工具  準備

　　1： Preparation: Preparation of survey site personnel and tools

　　二：機械部件安裝

　　2： Installation of mechanical components

　　1：導軌安裝     1） 支架位置確定：  a)最高 最低 0.5米，中間2.5米b)支架在建筑梁上，誤差小于300mm2）支架尺寸要求： 水平誤差小于5mm（橫。縱）3）導軌尺寸：     a）垂直誤差 單根全長小于1mm 每0.7/5000連續三段三次b）相對誤差 轎箱側+2~~0mm   對重側+3~~0mmc）臺階與間隙：臺階（小于0.05mm）間隙（小于0.5mm）d）對角誤差： 小于等于3mm（中心誤差） 左右小于1mm   前后小于正負2mm

　　1: Installation of guide rail 1) Determination of bracket position: a) Maximum and minimum 0.5 meters, middle 2.5 meters b) Bracket on building beam, error less than 300mm2) Bracket size requirement: horizontal error less than 5mm (horizontal). Vertical) 3) Guide rail dimensions: a) Vertical error, single length less than 1mm, continuous three sections every 0.7/5000, three times. b) Relative error, car side+2~~0mm, counterweight side+3~~0mmc. Steps and gaps: Steps (less than 0.05mm) Gap (less than 0.5mm). d) Diagonal error: less than or equal to 3mm (center error), left and right less than 1mm, front and rear less than plus or minus 2mm

　　2：曳引機安裝  1)曳引機基礎高度確定 : 1/2導向輪直徑+導向輪最低離地大于150mm2)  鋼梁安裝：       a）2/1000 水平誤差b）平行誤差 小于6mmc）焊接厚度 大于6mmd）底板厚度 大于12mm               3）曳引機安裝：a）吊裝：嚴格按照超作要求進行超作b）尺寸要求：曳引機垂直誤差 小于2mm(有避震)小于1mm(無避震)  c） 制動器： 間隙 小于0.7mm   貼合面：大于80%

　　2: Traction machine installation 1) Determination of traction machine foundation height: 1/2 guide wheel diameter+minimum ground clearance of guide wheel greater than 150mm2) Steel beam installation: a) 2/1000 horizontal error b) Parallel error less than 6mmc) Welding thickness greater than 6mmd) Bottom plate thickness greater than 12mm 3) Traction machine installation: a) Lifting: Strictly follow the overtime requirements b) Size requirements: Traction machine vertical error less than 2mm (with suspension) less than 1mm (without suspension) c) Brake: Gap less than 0.7mm Fitting surface: greater than 80%

　　3：對重安裝：對重重量確定 自重+（0.4~~0.5）載重， 對重塊必須可靠固定.

　　3: Counterweight installation: The counterweight weight is determined by its own weight plus (0.4~~0.5) load capacity, and the counterweight block must be reliably fixed

　　4：曳引鋼絲繩：a）長度確定 ：采用實測方式b） 繩頭要求 ：1）截取長度 大于100mm   2）澆筑巴氏合金符合要求c）懸掛必須調整螺桿錐套長度 小于70mm

　　4: Traction wire rope: a) Length determination: measured method used b) Rope head requirements: 1) Cut length greater than 100mm 2) Pouring Babbitt alloy meets requirements c) Suspension must be adjusted with screw cone sleeve length less than 70mm

　　5：轎箱安裝 ：  1）轎箱安裝尺寸：水平小于1/1000   前后小于1/10002）導靴與導軌間隙： 左右共小于2mm3）安全鉗間隙調整 2~~3mm4）轎底水平度 1/1000（橫，縱）5）地坎水平度 1/10006）轎壁垂直度 1/1000（裝簧板，操縱板處）7）轎門與裝飾板間隙 客梯：小于6mm 貨梯：小于8mm8）安全觸板必須產生中心偏差為10mm9）懸掛門的偏心輪與門導軌間隙 小于0.5mm10）門鎖下端離地坎表面 客梯:<6mm   貨梯：<8mm11）門中心偏差：小于5mm

　　5: Car installation: 1) Car installation dimensions: horizontal less than 1/1000, front and rear less than 1/10002) Clearance between guide shoes and guide rails: less than 2mm3 on both sides) Clearance adjustment of safety clamps 2~3mm 4) Levelness of car bottom 1/1000 (horizontal and vertical) 5) Levelness of sill 1/10006) Verticality of car wall 1/1000 (at the spring plate and control plate) 7) Clearance between car door and decorative plate Passenger elevator: less than 6mm Freight elevator: less than 8mm 8) The center deviation of the safety contact plate must be 10mm 9) The eccentric wheel of the suspended door and the door guide rail clearance must be less than 0.5mm 10) The lower end of the door lock is less than the surface of the sill Passenger elevator:<6mm Freight elevator:<8mm 11) Door center deviation: less than 5mm

　　6：層門安裝：   1）門扇下端      客梯：小于6mm   貨梯：小于8mm2）門扇與門套   客梯：小于6mm   貨梯：小于 8mm3）地坎水平誤差   1/10004）廳門地坎與轎門地坎相對間隙 25~~30mm廳門地坎與轎門地坎相對誤差 小于正負1mm5）門鎖嚙合深度大于7mm6）門球與轎箱地坎間隙    5~~10mm門刀與廳門地坎間隙    5~~10mm

　　6: Installation of landing doors: 1) Passenger elevator at the bottom of the door leaf: less than 6mm; Freight elevator: less than 8mm2; Passenger elevator between the door leaf and the door frame: less than 6mm; Freight elevator: less than 8mm3; Horizontal error of the sill: 1/10004) Relative gap between the hall door sill and the car door sill: 25~30mm; Relative error between the hall door sill and the car door sill: less than plus or minus 1mm; 5) Door lock engagement depth greater than 7mm; 6) Gap between the door ball and the car door sill: 5~10mm; Gap between the door blade and the hall door sill: 5~10mm

　　7：地坎安裝：   1）緩沖器垂直誤差   0.5/10002）相對高度       小于2mm3）相對中心       小于 20mm4）緩沖器開關必須有效

　　7: Installation of the embankment: 1) Vertical error of the buffer is 0.5/10002) Relative height is less than 2mm3) Relative center is less than 20mm 4) Buffer switch must be effective

　　8：限速器：      1）機房限速輪垂直誤差 ： 小于0.5mm2）限速繩與導軌側面誤差：小于20mm3）地坑漲緊裝置離地必須符合要求

　　8: Speed limiter: 1) Vertical error of speed limiting wheel in the machine room: less than 0.5mm2) Error between speed limiting rope and guide rail side: less than 20mm3) The ground lifting device of the pit must meet the requirements

　　9：電器裝置：   1）控制屏尺寸要求：0.5米（左右）X 0.6米（后側）X 0.8米（前面）2）電纜在機房必須進入線槽并有可靠接地3）井道電纜不應有扭曲   電纜最低離地大于100mm4）井道線槽必須有可靠接地5）井道照明   0.5米（上下各離最高低端） 7米（燈與燈的距離）6）各類急停   必須有效

　　9: Electrical device: 1) Control screen size requirements: 0.5 meters (left and right) X 0.6 meters (rear) X 0.8 meters (front)

　　10：各種實驗： 1）慢速單層   2）慢速多層   3）快速單層   4）快速多層 5）平衡系數 6）制停實驗7）提升實驗   8）靜載實驗 電梯在最底層，150%載重，歷時10分鐘

　　10: Various experiments: 1) Slow single-layer, 2) Slow multi-layer, 3) Fast single-layer, 4) Fast multi-layer, 5) Balance coefficient, 6) Stopping experiment, 7) Lifting experiment, 8) Static load experiment. The elevator is at the bottom layer with a load of 150% and lasts for 10 minutes

　　本文由  濟寧電梯門套加工定制  友情奉獻.更多有關的知識請點擊  http://www.ljwszxbls.cn/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jining Elevator Door Frame Processing Customization For more related knowledge, please click http://www.ljwszxbls.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.